Dnyanamay

Open Access Open Access  Restricted Access Subscription Access

Printing Machine UV Lamp Temperature Control Panel


Affiliations
1 P.E. Society's Modern College of Engineering, Pune, India
 

Printing is done for various aspects such as for decorating purpose, information shearing through magazine, news paper, books, on textile etc. The design or text is printed on cloth or paper or wood. In printing there is problem to cure (dry) the ink after print. If it is not cure as early then there is possibility to sprayed the ink. The aim of this project is to control various aspects of curing such as level of ink, temp of lamp, moisture/humidity of ink and speed of fan by using PLC and Microcontroller.

Ink is spared over it which is needed to cure or dry. To fulfill this requirement a continuous monitoring and controlling is required. Monitoring is achieved by using Microcontroller.

Microcontroller translate the data on PC, all required levels for curing is set by microcontroller. Microcontroller set the level of ink, temperature level of UV lamp, moisture level of ink and speed of blowers.


User
Notifications
Font Size

  • J. Y. Zhang, I. W. Boyd, “Lifetime investigation of excimer UV sources, ” Applied surface science, vol. 168, pp. 296-299, December 2000.

  • M. Laroussi, X. Lu, V. Kolobov, and R. Arslanbekov “Power consideration in the pulsed dielectric barrier discharge at atmospheric pressure, ” J. Appl. Phys, vol. 96, 3028, 2004.

  • R. P. Mildren, and R. J. Carman, “Enhanced performance of a dielectric barrier discharge lamp using short-pulsed excitation, ” J. Phys. D: Appl. Phys. , vol. 34, No 1, L1-L6, January 2001

  • Tansheng Zhou, Jianjun Dong, Zongquan Song. Application study of digital PID controller in cockpit temperature autoregulating system, Journal of Measurement Science and Instrumentation, 2 (2013) 190-193.

  • Ali EtemGurel, IlhanCeylan. Thermodynamic analysis of PID temperature controlled heat pump system, Case Studies in Thermal Engineering, 2 (2014) 42-49.

  • Tomas Nahlovsky, Optimization of Fuzzy Controller Parameters for the Temperature Control of Superheated Steam, In 25th DAAAM International Symposium on Intelligent Manufacturing and Automation (DAAAM 2015), 100 (2015) 1547-1555.

  • Lei Wang, Wencai Du, Hai Wang, Hong Wu, Fuzzy self-tuning PID control of the operation temperatures in a two-staged membrane separation process, Journal of Natural Gas Chemistry, 17. 4 (2008) 409-414.


Abstract Views: 108

PDF Views: 79




  • Printing Machine UV Lamp Temperature Control Panel

Abstract Views: 108  |  PDF Views: 79

Authors

Pritika Arvind Patil
P.E. Society's Modern College of Engineering, Pune, India
Shilpa Joshi
P.E. Society's Modern College of Engineering, Pune, India

Abstract


Printing is done for various aspects such as for decorating purpose, information shearing through magazine, news paper, books, on textile etc. The design or text is printed on cloth or paper or wood. In printing there is problem to cure (dry) the ink after print. If it is not cure as early then there is possibility to sprayed the ink. The aim of this project is to control various aspects of curing such as level of ink, temp of lamp, moisture/humidity of ink and speed of fan by using PLC and Microcontroller.

Ink is spared over it which is needed to cure or dry. To fulfill this requirement a continuous monitoring and controlling is required. Monitoring is achieved by using Microcontroller.

Microcontroller translate the data on PC, all required levels for curing is set by microcontroller. Microcontroller set the level of ink, temperature level of UV lamp, moisture level of ink and speed of blowers.


References