Manufacturing Technology Today

Open Access Open Access  Restricted Access Subscription Access
Open Access Open Access Open Access  Restricted Access Restricted Access Subscription Access

Analysis of Machining Responses in EDM of Al6101-Se/B4C/CNT Composite


Affiliations
1 Sri Venkateswara University College of Engineering, Tirupati, Andhra Pradesh, India
     

   Subscribe/Renew Journal


In the present days, automobile and aerospace sectors are showing more interest on aluminium metal matrix composites (AMMCs) due to their attractive properties. The machining of AMMCs by EDM is a field of attention for researchers as conventional machining of MMCs is complex and difficult. In this work, experiments are conducted on a composite sample of Al6101-Se/B4C/CNT called AMMC using EDM according to Taguchi experimental design for different parameter combinations such as electrode wire type, TON, TOFF, and peak current. The experimental data of machining responses such as surface roughness, material removal rate, and kerf width are measured for each experimental run. Further, the influence of process parameters on responses is studied by analysing them and optimal processes parameters are identified. Analysis of Variance is also employed for the identification of the order of influential process parameters on responses. This study provides ideal machining condition which can be utilized to increase material removal rate, as well as to limit surface roughness. Finally, the experimental results are validated through confirmation tests.

Keywords

Aluminium Metal Matrix Composite, EDM, Taguchi, Analysis of Variance, Machining Responses.
User
Subscription Login to verify subscription
Notifications
Font Size

  • Anand Babu, K., & Venkataramaiah, P. (2018). Evaluation of aluminium hybrid metal matrix composites by analytical hierarchy process (AHP) method. Manufacturing Technology Today, 17(2), 3-14.

  • Anand Babu, K., & Venkataramaiah, P., & Saideepthi Yerrathota (2018). Material selection for preparation of aluminium hybrid MMCs. Material Today: Proceedings, 5(5), 12209-12222.

  • Bhanu Prakash, D., & Krishnaiah, G. (2017). Optimization of process parameters using AHP and VIKOR when turning AISI 1040 steel with coated tools. International Journal of Mechanical Engineering and Technology (IJMET), 8(1), 241-248.

  • Bhaumik, M., & Maity, K. (2017). Effect of machining parameter on the surface roughness of AISI 304 in silicon carbide powder mixed EDM. Decision Science Letters, 6, 261-268.

  • Bhaumik, M., & Maity, K. (2017). Effects of Process Parameters and Cryotreated Electrode On the Radial Overcut of AISI 304 in SiC Powder Mixed EDM. Surface Review and Letters, 24. https://doi.org/10.1142/S0218625X18500294

  • Bhuyan, R. K., & Routara, B. C. (2016). Optimization the machining parameters by using VIKOR and Entropy weight method during EDM process of Al–18% SiCp metal matrix composite. Decision Science Letters, 5(2), 269-282. https://doi.org/10.5267/j.dsl.2015.11.001

  • Dewangan, S., Biswas, C. K., Gangopadhyay, S. (2014). Influence of different tool electrode materials on EDMed surface integrity of AISI P20 tool steel. Materials and Manufacturing Processes, 29(11-12), 1387–1394.

  • Durga Prasad, K.G., Prasad, M.V., Bhaskara Rao, S.V.V. & Patro, C.S. (2016). Supplier Selection through AHP-VIKOR Integrated Methodology. SSRG International Journal of Industrial Engineering, 3(3), 1-6.

  • Dwivedi, A. P., & Choudhury, S. K. (2016). Effect of tool rotation on MRR, TWR and surface integrity of AISI-D3 steel using the rotary EDM process. Materials and Manufacturing Processes, 31(14), 1844-1852.

  • Dyzia, M., & OEleziona, J. (2008). Aluminium matrix composites reinforced with AlN particles formed by in situ reaction. Materials Science, 31(1), 17-20.

  • Jeykrishnan, J., Ramnath, B. V., Sureshrajan, G., Bharath, M. S., Savariraj, X. H., & Akilesh, S. (2016). Effects of die-sinking electro-discharge machining parameters on surface roughness in Inconel 825 Alloy. Indian Journal of Science and Technology, 9(41), 1-5.

  • Kumar, S., Batish, A., Singh, R., Singh, T. P. (2017). Machining performance of cryogenically treated Ti–5Al–2.5Sn titanium alloy in electric discharge machining: a comparative study. Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, 231(11), 2017–2024

  • Manjunath, T., Bhanodaya Reddy, G., & Venkataramaiah, P. (2017). Studies on Machining Characteristics & Optimal Process Parameters in Wire EDM of AL 6082 HNMMCS. Manufacturing Technology Today, 16(3), (2017), 32-38.

  • Payal, H., Maheshwari, S., & Bharti, P. S. (2017). Process modeling of electric discharge machining of Inconel 825 using artificial neural network. International Journal of Mechanical and Mechatronics Engineering, 11(3), 562-566.

  • Puri, Y. M., & Gohil, V. (2017) Experimental study of material removal rate in electrical discharge turning of titanium alloy (Ti-6Al-4V). IOP Conference Series: Materials Science and Engineering, 187, 1-6. https://doi.org/10.1088/1757-899X/187/1/012036

  • Rajyalakshmi, G., & Venkataramaiah, P. (2015). Application of Taguchi, Fuzzy-Grey Relational Analysis for Process Parameters Optimization of WEDM on Inconel-825. Indian Journal of Science and Technology, 8(35). https://doi.org/10.17485/ijst/2015/v8i35/50946

  • Ravi Kumar, K., & Nishasoms. (2019). DesirabilityBased Multi-objective Optimization and Analysis of WEDM Characteristics of Aluminium (6082)/Tungsten Carbide Composites. Arabian Journal for Science and Engineering, 44(2), 893-909. https://doi.org/10.1007/s13369-018-3353-5

  • Torres, A., Luis, C. J., & Puertas, I. (2015). Analysis of the influence of EDM parameters on surface finish, material removal rate, and electrode wear of an INCONEL 600 alloy. International Journal of Advanced Manufacturing Technology, 80, 123-140. https://doi.org/10.1007/s00170-015-6974-9


Abstract Views: 187

PDF Views: 1




  • Analysis of Machining Responses in EDM of Al6101-Se/B4C/CNT Composite

Abstract Views: 187  |  PDF Views: 1

Authors

M. Hari Prasad
Sri Venkateswara University College of Engineering, Tirupati, Andhra Pradesh, India
P. Venkata Ramaiah
Sri Venkateswara University College of Engineering, Tirupati, Andhra Pradesh, India

Abstract


In the present days, automobile and aerospace sectors are showing more interest on aluminium metal matrix composites (AMMCs) due to their attractive properties. The machining of AMMCs by EDM is a field of attention for researchers as conventional machining of MMCs is complex and difficult. In this work, experiments are conducted on a composite sample of Al6101-Se/B4C/CNT called AMMC using EDM according to Taguchi experimental design for different parameter combinations such as electrode wire type, TON, TOFF, and peak current. The experimental data of machining responses such as surface roughness, material removal rate, and kerf width are measured for each experimental run. Further, the influence of process parameters on responses is studied by analysing them and optimal processes parameters are identified. Analysis of Variance is also employed for the identification of the order of influential process parameters on responses. This study provides ideal machining condition which can be utilized to increase material removal rate, as well as to limit surface roughness. Finally, the experimental results are validated through confirmation tests.

Keywords


Aluminium Metal Matrix Composite, EDM, Taguchi, Analysis of Variance, Machining Responses.

References