Refine your search
Collections
Co-Authors
Journals
Year
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z All
Arora, Kanwer S.
- Repair Welding Procedure for P460NH Grade Steel Making Ladles
Abstract Views :471 |
PDF Views:11
Authors
Affiliations
1 Material Characterization and Joining (MCJ) Group, Research and Development Tata Steel, Jamshedpur, Jharkhand - 831001, IN
1 Material Characterization and Joining (MCJ) Group, Research and Development Tata Steel, Jamshedpur, Jharkhand - 831001, IN
Source
Indian Welding Journal, Vol 51, No 2 (2018), Pagination: 57-65Abstract
P460NH steels are extensively used in steel plants as ladle fabrication material. However, fusion welding of these steels leads to the problems such as cold cracking, residual stress, distortion and fatigue damage, these steels may require welding of the cracks that can develop during fabrication, handling and transportation stages, or during the service life of the plant. Present work explains repair welding procedure used for P460NH steel ladles welded by using shielded metal arc (SMA) welding and flux cored arc (FCW) welding processes and evaluation of its weld metal and heat affected area (HAZ) microstructure. Butter bead tempered bead technique followed to fill the joint groove and simulated repair welding of SMA and FCA welds was carried out at the weld/base metal interface, i.e. at the location at which cracks are usually reported to occur during fabrication. SMA repair welding procedure conforming to the ASME Boiler and pressure Vessel Code were used followed by post heating of welds at 300°C for 2 hours per 25mm thickness of the weld. Tensile properties, bend tests, hardness profiles, impact tests and metallography studies using scanning electron microscope (SEM) were determined for both SMA and FCA welds to evaluate simulated repair welds. Analysis of the test results showed that the cooling rate maintained by means of preheating, interpass and post heating plays an important role in repairing of P460NH steel weld cracks.Keywords
Repair Welding, Ladles, Welding Procedure, P460NH Grade Steel, Microstructure.
References
- Aloraier, Ibrahim R and Thomson P (2006); FCAW process to avoid the use of post weld heat treatment, International Journal of Pressure Vessels and Piping, 83, pp.394–398.
- Flat Products Made of Steels for Pressure Purposes–Part 3: Weldable Fine Grain Steels, Normalized English Version of DIN EN 10028-3:2009-09.
- Fairchild DP, Bangaru NV, Koo JY, Harrison PL and Ozekcin A (1991); A Study Concerning Intercritical HAZ Microstructure and Toughness in HSLA Steels, Welding Journal, 70(12), pp.321s-329s.
- Ebert HW and Winsor FJ (1980); Carbon steel submerged arc welds tensile strength vs. corrosion resistance, Welding Journal, 59(7), pp.193s-198s.
- Aidun DK and Savage WF (1984); Optimizing repair welding techniques in cast steels—Part I, Welding Journal, 63(11), pp.345s–353s.
- Bhaduri AK, Rai SK, Gill TPS, Sujith S and Jayakumar T (2001); Evaluation of repair welding procedures for 2.25Cr–1Mo and 9Cr–1Mo steel welds, Science and Technology of Welding and Joining, 6(2), pp.89-93.
- ASME Boiler and Pressure Vessel Code, Section XI, 217–223; Code Case N–236–1, 385–394; Code Case N–432, 757–760, ASME, New York, 1986.
- Zhang Y, Zhang H, Li J and Liu W (2009); Effect of heat input on microstructure and toughness of coarse grain heat affected zone in Nb microalloyed HSLA steels, J Iron Steel Research Inter, 16(5), pp.73-80.
- Lee CH, Bhadeshia HKDH and Lee HC (2003); Effect of plastic deformation on the formation of accicular ferrite, Mater Sci Eng A, 360(1-2), pp.249-257.
- Dhua SK and Sen SK (2011); Effect of direct quenching in the microstructure and mechanical properties of the lean chemistry HSLA-100 steel plates, Mater Sci Eng A, 528(21), pp.6356-6365.