Indian Welding Journal

Open Access Open Access  Restricted Access Subscription Access
Open Access Open Access Open Access  Restricted Access Restricted Access Subscription Access

Theoretical Thermal Model of MIG Welding of FSS (AISI 430) Using ANSYS and its Experimental Verification


Affiliations
1 Hatia, Ranchi, 834003, India
2 NIFFT, Hatia, Ranchi, 834003, India
     

   Subscribe/Renew Journal


Metallurgical and mechanical properties of a weldment depend on its cooling rate and temperature distribution during welding. Temperature distribution and cooling rate are responsible for formation of different microstructures and different size of grain in different zones. If cooling rate and temperature distribution can be predicted in advance it will help the design engineer at the design stage itself to design a good welded joint. Determination of cooling rate and temperature distribution in welding experimentally is very costly and time taking. In this work the cooling rate and temperature distribution was theoretically predicted using ANSYS14 and experimentally verified. For the theoretical thermal analysis, 3D modeling of thermal simulation of arc welding (MIG) process was done by using ANSYS14. The special feature of the analysis is the use of a fast iterative procedure during a single pass welding. Temperature dependent metal properties of AISI 430 were taken from standard data source and were utilized till to the liquid phase. Element shape '3-D 10-Node tetrahedral' (solid 87) was used in 3-D analysis. Conduction and convection are considered as heat transfer mode. The experimental values of welding speed, welding current, and arc voltage were used for theoretical analysis. Thermocouples were used to record welding temperature using data tracker and computer. Five thermocouples were fixed at the middle line of the plate to measure temperature distribution and cooling rate practically. Two plates of FSS were welded by MIG welding in butt joint position in single pass.

Keywords

Ferritic Stainless Steel, MIG Welding, Cooling Rate, Temperature Distribution, Thermocouple, ANSYS.
User
Subscription Login to verify subscription
Notifications
Font Size

  • Lippold JC and Kotecki DJ (2005); Welding Metallurgy and Weldability of Stainless Steels, John Wiley and Sons, p.87.

  • Tekriwal P and Mazumder J (1988); Finite element analysis of three-dimensional transient heat transfer in GMA welding, Welding Journal, Research and Development, pp.150s-156s.

  • Negi V and Chattopadhyaya S (2013); Critical assessment of temperature distribution in submerged arc welding process, Advances in Materials Science and Engineering, Article ID 543594, pp.1-9.

  • Kumar KS (2015); Investigation on transient thermal responses on 316L austenitic stainless steel and low carbon ferritic steel welding using pulsed Nd: YAG laser, Material Science & Engineering, 4(6), pp.1-9.

  • Ho GY and Chu TK (1977); Electrical resistivity and thermal conductivity of nine selected AISI stainless steels, CINDAS Report 45, Prepared by American Iron and Steel Institute, p.37.

  • ASM Handbook (1993); vol. 6, ASM International, p.71.

  • http://www.engineeringtoolbox.com/convective-heattransferd_430.html

  • ANSYS 14.5 Help Desk Element Type.

  • Pathak AK and Datta GL (1999); Three-dimensional finite element analysis of heat flow in arc welding, Indian Welding Journal, 32(3), pp.32-38.

  • Silva PN and Narayanan Sankar TK (1996); Finite element analysis of temperature distribution during arc welding using adaptive grid technique, Welding Journal, 75(4), pp. 123s-128s.

  • Ismail MIS and Afieq WM (2016); Thermal analysis on a weld joint of aluminium alloy in gas metal arc welding, Advances in Production Engineering and Management, 11(1), pp.29-37.


Abstract Views: 317

PDF Views: 8




  • Theoretical Thermal Model of MIG Welding of FSS (AISI 430) Using ANSYS and its Experimental Verification

Abstract Views: 317  |  PDF Views: 8

Authors

A. K. Pathak
Hatia, Ranchi, 834003, India
Ch. Sree Harsha
NIFFT, Hatia, Ranchi, 834003, India

Abstract


Metallurgical and mechanical properties of a weldment depend on its cooling rate and temperature distribution during welding. Temperature distribution and cooling rate are responsible for formation of different microstructures and different size of grain in different zones. If cooling rate and temperature distribution can be predicted in advance it will help the design engineer at the design stage itself to design a good welded joint. Determination of cooling rate and temperature distribution in welding experimentally is very costly and time taking. In this work the cooling rate and temperature distribution was theoretically predicted using ANSYS14 and experimentally verified. For the theoretical thermal analysis, 3D modeling of thermal simulation of arc welding (MIG) process was done by using ANSYS14. The special feature of the analysis is the use of a fast iterative procedure during a single pass welding. Temperature dependent metal properties of AISI 430 were taken from standard data source and were utilized till to the liquid phase. Element shape '3-D 10-Node tetrahedral' (solid 87) was used in 3-D analysis. Conduction and convection are considered as heat transfer mode. The experimental values of welding speed, welding current, and arc voltage were used for theoretical analysis. Thermocouples were used to record welding temperature using data tracker and computer. Five thermocouples were fixed at the middle line of the plate to measure temperature distribution and cooling rate practically. Two plates of FSS were welded by MIG welding in butt joint position in single pass.

Keywords


Ferritic Stainless Steel, MIG Welding, Cooling Rate, Temperature Distribution, Thermocouple, ANSYS.

References





DOI: https://doi.org/10.22486/iwj%2F2018%2Fv51%2Fi3%2F175003