Refine your search
Collections
Co-Authors
Year
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z All
Jacob, Into
- An Analytical Investigation On Design And Structural Analysis Of Cam Shaft Using Solid Works And Ansys In Automobiles
Abstract Views :147 |
PDF Views:0
Authors
Affiliations
1 Department of Mechanical Engineering, Budge Budge Institute of Technology, Kolkata – 700137, West Bengal, IN
2 Department of Mechanical Engineering, Nehru College of Engineering and Research Centre, Thrissur – 680597, Kerala, IN
3 Department of Mechanical Engineering, Saveetha University, Chennai – 602105, Tamil Nadu, IN
4 Department of Mechanical Engineering, St. Josephs Collegeof Engineering, Chennai – 600119, Tamil Nadu, IN
1 Department of Mechanical Engineering, Budge Budge Institute of Technology, Kolkata – 700137, West Bengal, IN
2 Department of Mechanical Engineering, Nehru College of Engineering and Research Centre, Thrissur – 680597, Kerala, IN
3 Department of Mechanical Engineering, Saveetha University, Chennai – 602105, Tamil Nadu, IN
4 Department of Mechanical Engineering, St. Josephs Collegeof Engineering, Chennai – 600119, Tamil Nadu, IN
Source
Indian Journal of Science and Technology, Vol 9, No 36 (2016), Pagination:Abstract
Objectives: This paper reports an investigation that was carried out for modelling and structural analysis of cam shaft. Methods/Statistical Analysis: The modelling of cam shaft is carried out using the software solid works and the structural analysis of the model is carried out by using Ansys software. Initially, the model is designed with Solid works software and then it is converted into Initial Graphics Exchange Specification (IGES) file. Then it is systematically analyzed using the IGES model of cam shaft. Experimental results under static load containing the stresses and deflection are predicted cast iron material. Findings: Testing was carried out for unidirectional different materials like ductile cast iron, nodular iron and carbon epoxy. By considering these materials, it is noted that the ductile cast iron is a good material compared to the nodular iron because the breakage of nodular cast iron is higher than the ductile cast iron. Application\ Improvements: Ductile cast iron is considered for making the cam shaft in vehicles because the cost of material slightly higher than nodular iron. In the development of modelling and also analyse by software helps to better result in design.Keywords
Cam shafts, Gray cast iron, Spheroidal cast iron, Carbon Epoxy, Solid works and Ansys.- Design and Computational Investigation of Double Piston U-Shaped Single Connecting Rod in Remodelled Internal Combustion Engines
Abstract Views :163 |
PDF Views:0
Authors
G. Ragul
1,
Arun Thampi
2,
Tedy Thomas
2,
C. P. Praveen
2,
Into Jacob
2,
V. Jayakumar
3,
S. Naveen Kumar
4
Affiliations
1 Department of Mechanical Engineering, Budge Budge Institute of Technology, Kolkata – 700137, West Bengal, IN
2 Department of Mechanical Engineering, Nehru College of Engineering and Research Centre, Thrissur – 680597, Kerala, IN
3 Department of Mechanical Engineering, Saveetha School of Engineering, Saveetha University, Chennai – 602105, IN
4 Department of Mechanical Engineering, St. Josephs College of Engineering, Chennai - 600119, Tamil Nadu, IN
1 Department of Mechanical Engineering, Budge Budge Institute of Technology, Kolkata – 700137, West Bengal, IN
2 Department of Mechanical Engineering, Nehru College of Engineering and Research Centre, Thrissur – 680597, Kerala, IN
3 Department of Mechanical Engineering, Saveetha School of Engineering, Saveetha University, Chennai – 602105, IN
4 Department of Mechanical Engineering, St. Josephs College of Engineering, Chennai - 600119, Tamil Nadu, IN
Source
Indian Journal of Science and Technology, Vol 9, No 36 (2016), Pagination:Abstract
Objectives: This paper aims at studying force distribution characteristics and load with standing capability of a remodelled IC engine piston connecting rod arrangement where the conventional single piston single connecting rod arrangement is replaced by linking two pistons with a single connecting rod. Methods\Statistical Analysis: 3D Modelling of the arrangement is carried out using Solid works while force analysis of the model is done using ANSYS workbench. Parallel twin cylinder 4 stroke petrol engine is utilized as reference for creating the model and analysis purpose. Findings: The results gives the theoretical evidence that there can be a considerable reduction in engine weight and complexity with this new arrangement with stress, deformation and strain values lying within the boundary. Applications\Improvements: This arrangement gives extra room for lubricants thereby indeed indirectly increasing performance characteristics.Keywords
Aluminium Alloy, Brake Power, Connecting Rod, Piston, Internal Combustion Engine, Solid Works and Ansys.- An Investigation in Analysis of Dry Turning in MQL Method for Predicting Tool Wear and to Improve Surface Roughness
Abstract Views :152 |
PDF Views:0
Authors
Affiliations
1 Department of Mechanical Engineering, Budge Budge Institute of Technology, Kolkata, IN
2 Department of Mechanical Engineering, St. Josephs College of Engineering, Chennai, IN
3 Department of Mechanical Engineering, Nehru College of Engineering and Research Centre, IN
4 Department of Mechanical Engineering, Saveetha University, Chennai, IN
1 Department of Mechanical Engineering, Budge Budge Institute of Technology, Kolkata, IN
2 Department of Mechanical Engineering, St. Josephs College of Engineering, Chennai, IN
3 Department of Mechanical Engineering, Nehru College of Engineering and Research Centre, IN
4 Department of Mechanical Engineering, Saveetha University, Chennai, IN